Why do slab leaks stay hidden for so long?
A slab leak has nowhere to show. The water spreads into the ground, and the concrete holds it until the warm or damp spot finally reaches the flooring.
Slab homes sit on compacted soil, and the water from a leak in the slab moves into that soil and under the edge of the concrete. Because the surface of the slab absorbs and releases moisture slowly, a leak can run for a long time before anything is visible above the floor.
The first clue is often a feeling rather than a stain. A patch of tile is cooler or warmer than the rest of the room, or a wood floor cups near one wall. Those signs are early, and a homeowner who notices one should act before the moisture reaches the walls and the framing above.
Why does a slab leak affect the walls as well as the floor?
Water in the slab can wick upward into the block wall base and the lower drywall. The damage often runs along the perimeter of the room, not just the spot on the floor.
Concrete block is porous, and water that reaches the slab edge can travel up the block into the wall cavity. The lower drywall and the insulation then soak, and the paint at the base of the wall may bubble or peel. The wall base is therefore checked along the full length of the wet zone.
Mold grows where the wall base stays damp and the air stays humid. A musty smell along a wall in a room with no obvious leak is a good reason to check the slab edge, and a technician will take readings there as well as on the floor.
How is the leak located without tearing up the whole floor?
Water meter readings, pressure checks and a thermal camera narrow the search. The flooring is opened only over the area the evidence points to.
A technician shuts off every fixture and reads the water meter over a set period. If the meter keeps moving with everything off, water is leaving the system, and the pressure check on the supply lines helps show whether the leak is inside the slab or in an accessible section of the house.
The thermal camera then shows the wetter and cooler ground beneath the flooring. Readings at the surface confirm the reading, and the crew marks the boundary. The method does not guarantee the exact pipe location, but it reduces the area that has to be opened, which keeps the disruption down to what the leak requires.
Who repairs the line, and what does the restoration crew do?
A plumber repairs the line. The restoration crew removes the wet flooring, dries the slab and documents the work so the plumber can scope the repair.
The repair of a supply or drain line under the slab is a plumbing job, and it should be carried out by a plumber. Titusville Water Damage Restoration does not do plumbing repairs. The crew's work begins where the plumber's work ends, with drying and restoration of the surfaces the water reached.
A clear record helps both trades. The leak location, the wet area and the drying readings are written up for the homeowner. Once the plumber has finished and the slab is dry, the flooring and the wall base can be replaced by whichever contractor the homeowner chooses.
How long does a slab dry after a leak?
A slab takes longer than framing to dry, and the drying time depends on how long the leak ran and how humid the house has been.
Concrete holds water deep in its mass, so the drying is measured by readings taken at the surface and at the slab edge. The crew uses air movers and dehumidifiers and returns on a schedule until the concrete reaches its dry target. A small leak that stopped quickly may dry in several days, while a long leak can take much longer.
Florida's humid air is the main variable. A closed room in summer holds moisture the equipment has to pull out, and a house with the air conditioning off can rise in humidity overnight. The crew checks the air as well as the slab, and it adjusts the equipment to the conditions it finds.
What should a homeowner do while waiting for the crew?
Shut off the water to the house if the leak is known, keep the affected room clear and avoid walking on wet tile or lifted flooring.
If the homeowner knows which fixture or line is leaking, closing its shutoff valve or the main valve stops more water entering the slab. Note the time the water meter reads before and after the shutoff, because that reading helps the technician confirm whether the leak is still active.
Move rugs and furniture off the suspected area, and do not walk on lifted flooring, which can cut feet or slip. Call (833) 490-5225 at any hour for a technician, and keep the phone away from standing water while the room is checked.